I replaced an
Air Conditioning compressor on my 1998 S-10 4-cyl (2.2L engine)
pick up 3 to 5 years ago. The system is once again not working, though
the electric A/C compressor clutch kicks in OK. Pressure is nearly the
same between the high and low sides, which I believe whas what
happened before I replaced the compressor the last time.
I had replaced it with a Chinese made copycat compressor and a
receiver drier, and possibly an orifice tube (not sure about the last
item). I hooked everything up loosely and let a backyard (but
licensed) A/C mechanic finish the job with the proper O-rings, oil,
refrigerant, etc., and the job included a flush of the condenser and
evaporator coils and the connecting plumbing.
I do not know if the flush was thorough enough but I did watch him
flush the system. I plan to purchase the canister to put the flushing
fluid into to flush my system before putting the new compressor and
receiver-drier on and doing a vacuum on the system then charging it.
I would like to do the replacement myself this time. I have the gauge
set and a vacuum pump and have used it since the last time I got the
replacement done on other vehicles, including evacuating and
recharging an A/C system on a 97 Mazda Protege. I can follow
directions well enough as I've rebuilt a Honda Accord engine by
following the instructions in a repair manual and asking a few
questions of friends who have experience with this sort of thing.
First, I've found a complete parts set of a compressor and receiver
drier on Rock Auto dot com for a reasonable price. I can add less than
$100 more and get a condenser coil, but I am not sure I need it (see
next paragraph).
I have read where some of the very newest vehicles use such tiny tubes
in the condenser coils that they are near impossible to flush.
However, I don't know if they were that small in '98 or not, so I need
some input here as to whether I can just flush the original condenser
and re-use it or not???
Also, when I flush the various sections of the system, I would
appreciate knowing which hose/port and direction to flush the fluid
through, or does it matter which direction I force the fluid through
the system when it's opened up???
I don't plan to be stingy with the fluid even though it's not cheap.
If I use a whole gallon on the system that's fine with me if I need
to. But if I only need to buy a fraction of that then I can save some
money there, too. So how much of this flush fluid will I need to buy?
Does it store well when unused for a long time if tightly sealed?
I will also need to know what sort of torque to apply to the bolts on
the fittings at the compressor and anywhere else I need to be careful
about torque. I might not be able to torque the hose fittings as I
only have a wrench which will fit sockets but I am open to any
suggestions or help. This is my first A/C compressor replacement job
so I want to approach it cautiously and get whatever advice that might
be helpful. The previous replacement I didn't really do any of the
technical work, though I"ve learned about the evacuation and recharge
process and have done that successfully on the Mazda.
Any help with this would be appreciated. I've posted this to the two
groups which have helped me the most in my various automotive repairs.
Both groups have helped me in the past with my S-10, and I thank you
all for that.
I will wait a few days for replies to come in before I order anything.
If I need to buy a condenser coil also (and I'd rather not so I can
avoid the extra work of removing and replacing it in this hot summer
weather), I can get it cheaper in a set from Rock Auto.
If any of you use Rock Auto and know how to find generic items like
the flush fluid instead of me buying it through ebay (or if you have a
better source), please share that, too. I can find model-specific
parts very easily but when it comes to the generic stuff I find it
hard to find there, but I would think they would have those items too.
Thanks in advance.